One Solution™ Dispenser - Sidekick Foamer

Portable Foam Cleaning System

Item #125319

One Solution™ Dispenser - Sidekick Foamer

One Solution™ Dispenser - Sidekick Foamer

Portable Foam Cleaning System

Item #125319

Options:

Need Assistance? Call us 1-800-321-8180

Favorite Share

Compact design is lightweight and portable for use all around the facility
Integrated dilution tips dilute chemicals for accurate, cost-effective use
Integrated spray-and-rinse nozzle makes this an all-in-one system

Product Description

The One Solution™ Sidekick Foamer is a versatile and convenient foaming, spraying, and rinsing system ideal for a wide variety of cleaning applications.

VERSATILE:
The One Solution™ Sidekick Foamer is an innovative and versatile foaming, spraying and rinsing system offering all of these functions in one device. Choose either the foaming or spraying nozzles to apply rich, clinging foam or spraying solution, then disengage the chemical supply to provide a thorough rinse using the Sidekick’s integrated rinse function. Easily select either a wide-angle spraying pattern or a powerful jet-stream simply by rotating the rinse-pattern selector. The Sidekick Foamer is portable and mobile. There is no need to be tethered to the wall and there is no need to mount to a cart. Simply attach to a standard water hose and start cleaning.

ECONOMICAL:
The One Solution™ Sidekick Foamer is part of State’s One Solution™ dilution program which offers users safe, accurate and cost effective dispensing every time. The Sidekick utilizes adjustable dilution tips which provide precise dilution ratios ranging from 1:7 on the heavy side all the way to 1:256 on the light side. Its integrated pressure regulation technology assures that dilution is consistent and accurate even across a wide range of water pressures.

MARKETS:
Schools Universities
Fast Food Facilities
Fine Dining
Hotels & Logding
Healthcare Facilities
Supermarkets Food Retailers

Directions for Use

1. Find suitable place close to water source for unit. Mounting bracket should be installed approx. 5’ from the floor. Level bracket and mark holes. Drill 9/32” holes and install mounting anchors and screws in bracket. 2. Remove cabinet cover and hang cabinet on bracket. Mark hole for lower cabinet screw. Remove cabinet and drill 9/32” hole. Install anchor and screw in lower cabinet hole. When mounting unit, do not mount more than 5 feet from the floor. Also, never mount your concentrate container higher than the unit. Keyhole slots are also provided in the cabinet back if the mounting bracket won’t be used. 3. Select a metering tip (see next section), and insert into hose barb on eductor body. (Repeat for all eductors.) 4. Supply tube should reach from hose barb on eductor to bottom of the concentrate container. Cut supply tube provided to length required. Slide a ceramic weight over one end of tube and slide a foot valve into the same end of the tube. (Prepare a tube for each eductor.) 5. Push other end of supply tube over the hose barb/metering tip on the eductor. (Repeat for all eductors.) 6. Place foot valve ends of supply tubes into concentrate containers. REMEMBER TO CHECK FOOT VALVE STRAINERS REGULARLY FOR CLOGGING: CLEAN IF NECESSARY. 7. A short discharge tube is used with the 1GPM eductor; minimum tube length is 8 inches (20cm) for proper operation.
Longer tubes (4 feet) are used with a 3.5 GPM eductor. Slide end of tube over eductor discharge outlet. (Repeat for all eductors.) Hooks may be installed on longer tubes to allow discharge tube to conveniently hang from dispenser when not in use. 8. Replace cabinet cover. Guide supply tubes through slots in sides of cabinet cover. Push the sides in, behind the latch holes, to snap the
cover in place. The two screws provided may be installed in the holes in the cabinet sides to prevent easy removal of cover. 9. Connect water supply hose of at least 3/8” ID to water inlet swivel. (Minimum 25 PSI pressure, with water running, is required for proper operation.) Connect opposite end of hose to water supply. Turn water supply on. 10. Purge air from the system by depressing the buttons briefly. There may be some water discharge from the eductor vents until the air is purged. 11. Push button to start flow of desired water/concentrate solution, and hold until supply tube is primed (filled). Then push the button whenever dispensing is desired, and release button to stop flow of solution. If you wish to be able to lock the button in the “on” position: Depress button and slide
button lock up. To unlock, depress button and release. 12. It is essential that the discharge hose not be obstructed. If discharge is restricted, water will flow out the eductor
vents. Do not start to operate the dispenser with liquid in the discharge tube.